AC power supply PCR-LE2 series

Specifications


Option Specifications

TYP: These are typical values. These values do not guarantee the performance of the PCR-LE2 Series.

TOP

Communication interface (GPIB/ USB/ LAN)

The specifications of the IB05-PCR-LE (GPIB), US05-PCR-LE (USB), and LN05-PCR-LE (LAN) interface boards are provided below.

GPIB

Complies with IEEE Std 488.1-1987

SH1, AH1, T6, L4, SR1, RL1, PP0, DC1, DT1, C0, and E1

24-pin connector (receptacle)

  

Message terminator

LF or EOI during reception, LF + EOI during transmission

Primary address

1 to 30

USB

Complies with the USB 2.0 specifications. Data rate: 12 Mbps (full speed), Socket B type

  

Message terminator

LF or EOM during reception, LF + EOM during transmission

Device class

Complies with the USBTMC-USB488 device class specifications

LAN

IEEE 802.3100Base-TX/10Base-T Ethernet

Complies with the LXI Specification Ver.1.3 Class C, Data rate: 100 Mbps (Auto negotiation, full speed)

AUTO MDIX function

IPv4, RJ-45 connector (Category 5; use a straight cable.)

  

Communication protocol

VXI-11/HiSLIP/SCPI-RAW

Message terminator

VXI-11, HiSLIP: LF or END during reception, LF + END during transmission

SCPI-RAW: LF

Controlling the Output Using External Analog Signals

The following specifications specify the comprehensive performance achieved when the Analog Interface is installed in the PCR-LE2 AC power supply. Other specifications not given here comply with those for the PCR-LE2 AC power supply.

  

EX05-PCR-LE

EX06-PCR-LE

Input terminal

Maximum allowable input voltage

±15 V

Type

BNC

Input impedance

10 kΩ ±10 %

Isolation voltage

±63 Vpeak

Input voltage range

0 V to 1.5 Vrms sine wave

0 Vdc to +10 Vdc

Input frequency range*1

1 Hz to 2k Hz (Sine wave)

1 Hz to 200 Hz (Rectangular wave)

DC

---

Frequency characteristics

DC to 5k Hz: -3dB or less

with respect to 200 Hz (On input of sine wave of 0.5 Vrms)

---

Voltage amplification ratio (L, H range)

100x, 200x

(Outputs a 0 Vac to 150 Vac/0 Vac to 300 Vac with respect to an input of 0 Vac to 1.5 Vac)

15x, 30x

(Outputs a 0 Vac to 150 Vac/0 Vac to 300 Vac with respect to an input of 0 Vdc to 10 Vdc)

Frequency setting range

---

1 Hz to 999.9 Hz

Output voltage distortion ratio*2

PCR-LE specifications + 0.5 % or less

Output voltage temperature coefficient

PCR-LE specifications + 200 ppm/°C(TYP)

Insulation resistance

  

Between input (BNC) and chassi, input(BNC) and input,

input (BNC) and output

500 Vdc, 30 MΩ or more

Withstand voltage

Between input (BNC) and output,

input (BNC) and output

500 Vac for 1 minute

Status signal output*3

OUTPUT ON STATUS

Turns on when the output is on.

ALARM STATUS

Turns on when an alarm/trouble is detected.

BUSY STATUS

Turns on when the busy status.

OOR STATUS

Turns on when the current limit is exceeded and when overload occurs.

External control*4

OUTPUT CONTROL*5

Output on with a low level signal/Output on with a high level signal.

SEQ RUN*5

Run the sequence with a low level signal/Run the sequence with a high level signal.

ALARM CLR*5

Alarm clear with a low level signal/Alarm clearwith a high level signal.

SHUT DOWN*6

Output off with an open circuit/Output off with a short circuit

*1. The measurable range of voltage, current, and power is DC and 1 Hz to 999.9 Hz
Set the frequency according to the input waveform period.

*2. When DC current is applied for EX06-PCR-LE or when a sine wave with distortion ratio of 0.1 % or less is applied for EX05-PCR-LE.

*3. Open collector outputs of photocouplers (30 Vdc, 8 mAmax.)

*4. Set the logic using CONFIG settings. The internal circuit is pulled up to 12 V through 1.3 kΩ.

*5. HIGH: Input terminal voltage of 11 V to 12 V or open; LOW: Input terminal voltage of 0 V to 1 V

*6. Open: Open or input terminal voltage of 11 V to 12 V; Short: Input terminal voltage of 0 V to 1 V

TOP

AC power supply PCR-LE2 seriesAC power supply PCR-LE2 series
Specifications